01/06/2023Borealis introduces the Bornewables™ line of Queo™, a range of plastomers and elastomers based on renewable feedstock. The introduction follows the International Sustainability and Carbon Certification (ISCC PLUS) of Borealis' production site for the Queo™ portfolio, in Geleen, the Netherlands.
01/06/2023ENGEL helps injection moulding processors optimize product changeover times through customized training and technologies such as the Setup wizard to achieve higher productivity, lower unit costs and more profit.
18/05/2023The company LAPP is using a new bio-based plastic from BASF for the sustainable version of its ETHERLINE® FD P Cat.5e for Industrial Ethernet. The bio-based plastic is Elastollan® N, the thermoplastic polyurethane from BASF, which is part of its circular economy strategy.
16/05/2023Eight to ten times on average a wooden pallet is used in the handling area of logistics before it shows a defect and has to be sorted out. This is neither particularly economical nor good for the environment. Pallets made of plastic offer a more sustainable solution.
11/05/2023Covestro AG offers a polycarbonate with a 90 percent recycled content of plastic from post-consumer waste (PCR) that can be used in consumer electronics, among other applications. The company is collaborating with Jabra on the Evolve2 headset and making progress on climate-neutral solutions through mass balancing.
04/05/2023Evonik Industries AG has invested in the British company Interface Polymers Ltd. This investment from the Sustainability Tech Fund strengthens Evonik's position in sustainable products and recycling processes. Interface Polymers' technology enables easier processing and recycling of plastics.
27/04/2023The two companies BluCon Biotech GmbH and LG Chem Ltd entered into an investment agreement. Together, they plan to work on a novel process to convert lignocellulosic non-food raw materials into high-purity lactic acid.
24/04/2023Kazakhstan is the most economically advanced country in Central Asia and plans to increase industrialization, which will increase plastics consumption. Central Asia Plast World is the most important business platform for plastics and rubber in Central Asia and will be held in Almaty in September 2023.
24/04/2023Plastic pollution is a serious threat to human health and the environment. After years of awareness-raising, there is strong and widespread alignment on the need to act. This was the unmistakable and welcome message from the U.N.'s first negotiating session on a global agreement to end plastic waste in December.
20/04/2023Project STOP, co-funded by Borealis and Systemiq, has created positive social and environmental impact in three cities in Indonesia, including the launch of the scale-up programme Project STOP Banyuwangi Hijau from Muncar into the Banyuwangi Region.
20/04/2023The company Covestro plans to further increase its global production capacity for polycarbonate (PC) specialty films by starting to build new extrusion lines at the Map Ta Phut Industrial Park in Thailand. The completion is planned by 2025 and the investment is in the higher double-digit million euro range.
13/04/2023In a study under the leadership of the ETH Zurich, the scientists point out that plastic products must be better aligned with the circular economy in future. The study finds that circular plastics are feasible within planetary boundaries. This would require at least 74 percent of the plastic to be recycled.
12/04/2023Megh Group company T3 (EPZ) Limited is going to install the first PET recycling system for bottle-grade rPET and resin in Kenya and Eastern Africa, a Starlinger recoSTAR PET 165 HC iV+ recycling line, in Athi River just outside Nairobi.
12/04/2023Röchling Industrial integrated the Röchling Direct Manufacturing Center from Waldachtal into the Röchling Industrial Laupheim at the Burgrieden site. The international plastics processor takes an important step in the industrialization of its 3D printing competencies and continues to focus on additive manufacturing.
05/04/2023With the "Product Carbon Footprint Engine" developed by LANXESS, the CO2 footprint can be calculated automatically for the Group's products. With this innovation, the speciality chemicals company aims to help its customers achieve their sustainability goals.
30/03/2023The first edition of the K China Symposium was successfully held at the Shanghai International Convention Centre on 23 March 2023. Participants praised the opportunity for professional exchange, business expansion and inspiration offered by this new, international platform.
20/03/2023The company Covestro will build its largest Thermoplastic Polyurethanes (TPU) site in Zhuhai, China. The TPU site will be built in three phases. The first phase will be completed in late 2025 and the final phase in 2033.
20/03/2023The two companies LyondellBasell and KIRKBI signed an agreement to make an investment in the company APK. APK has developed the unique solvent-based Newcycling® process, which separates the different polymers of multi-layer packaging materials and produces recycled materials with a high degree of purity suitable for new packaging materials.
13/03/2023The company Borealis is using its Borcycle™ C chemical recycling process to recycle crosslinked polyethylene (PE) types into recycled polyethylene. The EverMinds™ approach provides innovative and viable solutions to recycling challenges in the Wire & Cable and Infrastructure industries.
06/03/2023What do a tunnel and hiking boot have in common? Both have a membrane that prevents the ingress of rain. In the case of the tunnel, the Norwegian company Oldroyd is an expert for the membrane and its injection-molded fixing product. It uses CX machines from KraussMaffei and 100% sea plastics.
06/03/2023Neste, Uponor, Wastewise and Borealis have successfully produced pipes made of cross-linked polyethylene (PEX) which was based on feedstock gained from chemically recycled post-industrial waste plastic from PEX pipe production, using an ISCC PLUS certified mass-balancing approach. The partner companies believe this project is among the first implementations of chemical recycling of PEX.
01/03/2023Both healthcare and life sciences applications – ranging from drug delivery devices, wellness and wearable devices, to single-use containers for biopharmaceutical manufacturing – all have one thing in common. They must be tough and durable and able to withstand everyday use while maintaining their structural integrity.
01/03/2023Specialty chemicals company LANXESS and French energy group TotalEnergies have entered into a cooperation on the supply of biocircular styrene. Unlike conventional styrene, the raw material used by TotalEnergies is based on tall oil, which is derived from a tree resin and is a by-product of pulp production.
21/02/2023Imballaggi Alimentari, an Italian based company specialized in the production of ice cream packaging, has launched the Remaxigel boxes made of Styropor® Ccycled™. The boxes made of EPS (expandable polystyrene) boast excellent performance and were primarily designed for artisanal ice-cream shops.
21/02/2023SABIC, a global leader in the chemical industry, collaborates with Scientex in the packaging value chain to enable the manufacturer to develop material for the world’s first flexible food packaging made based on advanced recycled OBP, using SABIC® certified circular polypropylene (PP). The material is being used in a premium brand noodles packaging sold in Malaysia.
15/02/2023Plastic is a resource without which our life today would not be possible - and thanks to recycling, we can even use it several times over. However, we know from reports what can happen if the recycling process does not run properly: the plastic sometimes ends up in the sea. Getting it back into circulation from there and turning it into a usable product is not easy.
14/02/2023Chemical companies Covestro and LANXESS are cooperating in the energy-intensive production of basic chemicals at their Lower Rhine sites in Germany and make them more climate friendly. LANXESS procures chlorine, caustic soda and hydrogen from the ISCC PLUS-certified sites of Covestro in Leverkusen and Krefeld-Uerdingen.
31/01/2023Studies show that we are up to nine times more likely to remember something we have experienced in virtual reality. This knowledge can also be interesting for the plastics industry. With the iguversum, igus has created a digital space in which the manufacturer's products can be discovered. In the future, engineering projects will also be carried out there.
03/01/2023Many raw materials deserve a second life, and especially in view of resource conservation and the circular economy, the reuse of raw materials is particularly important. Evonik shows how it's done: The company produces PA-12 elastomers from old tires.
21/12/2022As the saying goes, one cannot make an omelette without breaking eggs – in a metaphorical sense, this is also the case when it comes to the 3D printing process. In most cases, material residue must be removed manually and then discarded. Cubicure delivers a different way that's automated, customizable, and sustainable.
08/11/2022Polymers are as diverse as their chemical composition. Plastics come in hard, soft, flexible, brittle, opaque, transparent - just as required. They impress with their durability, cost-effectiveness, impermeability to water, high formability, corrosion resistance and low weight. This makes them the ideal building material - and an environmentally friendly alternative to other materials.
02/11/2022The demand for high-quality recyclates has exceeded the supply on the market for years. So far, too much high-quality plastic is still being burned as waste instead of being recycled. The Berlin-based start-up Circleback wants to change that by setting up a deposit system for plastic packaging from the bathroom.
28/10/2022After about 25 years, the rotor blades of a wind turbine have usually had their day. But what happens to them then? Together with the Institute for Energy and Circular Economy (IEkrW), the Fraunhofer Institute for Wind Energy Systems (IWES) is developing concepts in a project that should enable rotor blades to be better recycled and reused.
26/10/2022Steinert.view® is a flexible and reliable monitoring solution for STEINERT sensor-based sorting machines. Performance data collected is visualized in a web app so that operators can see at a glance whether machines are currently producing, whether there are changes in production, or whether there is potential for optimization.
13/10/2022The set-up for K 2022 at the Düsseldorf Trade Fair is in full swing. The trade fair's logistics team is making sure that everything runs smoothly. Werner Arnold, Team Manager Logistics, explains in an interview all the things that need to be taken into account until all the halls at K are filled.
11/10/2022The MAM company is accelerating circular economy measures in partnership with Borealis through the launch of MAM Original Pure pacifiers and packaging enabled by Borealis Bornewables™ portfolio of recyclable polyolefins. Upstream value chain partner Neste is the supplier of renewable feedstock Neste RE™ based on waste and residue streams for the manufacture of Bornewables polypropylene.
11/10/2022The filling of a mold determines the quality of the resulting molded part. But what if insight into the filling process of particle foams is not available and thus control is lacking at this crucial point in the production process? A new transparent experimental mold made of acrylic glass developed by Neue Materialien Bayreuth (NMB) has put an end to this dilemma.
04/10/2022Communication is key, and this also applies to machines, since the ability of machines to communicate has economic advantages. However, this first requires a common linguistic basis, because then the machines can be used particularly efficiently.
03/10/2022A new technology from Covestro weakens the bond strength of PU adhesives. Laminated films in multilayer packaging can be separated after use and the individual materials can be recycled later. At the K 2022 trade fair, the team will be presenting the technology to the plastics industry for the first time.
03/10/2022ARCUS plans to start up first commercial pyrolysis plant for mixed plastic waste in Germany and will supply the company BASF SE with pyrolysis oil. This will enable further expansion of BASF's ChemCyclingTM business. The Agreement foresees take-up of up to 100,000 tons of pyrolysis oil per year.
19/09/2022Covestro plans to set up its first dedicated mechanical recycling (MCR) plant for polycarbonates at its integrated site in Shanghai. The company also plans to convert an existing compounding facility in Thailand into a mechanical recycling plant.
12/09/2022The chemicals company LANXESS aims to make its upstream and downstream supply chains climate-neutral by 2050. In order to achieve the so-called Scope 3 targets, LANXESS has launched the Net Zero Value Chain Program. The focus is on sustainable raw materials, green logistics and climate-neutral products.
05/09/2022A lot is happening in the field energy technology, not least as a result of rapidly rising energy prices. Spurred on by falling costs for renewable energy technologies, innovative storage solutions, intelligent energy management systems and new opportunities are also opening up for industrial and commercial companies.
02/09/2022Thomas Franken talks about his expectations for K2022, the challenges the industry faces and what technology is likely to develop in the coming years.
01/09/2022The BASF company is focusing on renewable energy in the field of electricity supply in the United States. BASF enables renewable energy projects by signing virtual power purchase agreements (VPPAs) totaling 250 MW. In addition, the amount of solar and wind energy in the grid offsets the energy supply of more than 20 production sites.
30/08/2022Successful business means sustainable business. Because according to KraussMaffei, sustainability has both ecological and economic advantages. Recently, the company reaffirmed its goal of being climate-neutral by 2030. Its strategy includes recycling solutions, energy-efficient construction and heating, and sustainable product development.
16/08/2022With the Packaging Act, Germany is taking a further step towards an all-encompassing raw material cycle for packaging. One of the requirements aims to significantly increase the amount of recyclable packaging. Packaging used in mail order or "dispensed" for to-go products has recently been required to be registered in the LUCID Packaging Register.
03/08/2022To improve plastic compounds and meet stringent fire safety requirements, BASF and THOR GmbH are using their joint expertise in flame retardants. The focus is on developing alternatives to halogen-containing additives.
02/08/2022Those who work meticulously to design a product can hardly await the day they can hold the finished item in their hands. Alpla is a company headquartered in Hard, Austria, that speeds up this process. Customers can convert their ideas into reality and ideally leave Alpla's STUDIOa with a prototype in hand.
25/07/2022The KraussMaffei company confirms a sustainable corporate strategy: Climate neutrality in eight years. The consistent focus is on Circular Economy. One of the largest roof-mounted photovoltaic systems in Europe is currently being built at the new main plant in Parsdorf.
12/07/2022At the heart of any modern robot is a gearbox. Now imagine a robot with its "heart" made of plastic. It’s simply marvelous. But that’s not the only benefit users can expect from the new cobot (collaborative robot) by igus: the device is also lightweight, portable, and affordable.
11/07/2022Covestro is researching material solutions for sustainable energy generation at its new Wind Technology Center. They are focusing on the optimization and new development of PUR resins in collaboration with customers.
08/07/2022The pandemic. Supply chain ruptures. The Great Resignation. China trade tensions. Climate change and extreme weather events. Soaring inflation. Stock market volatility. The war in Ukraine. Seldom in our lifetimes have we experienced such an extended period of disruption and uncertainty.
29/06/2022Thermoforming is a process that requires various tool systems. Unfortunately, if the latter originate from different manufacturers, they often cannot be used together in one system. Illig took on the challenge and came up with a successful solution.
21/06/2022Solvay launched the Kalix® 10000 series, a partially bio-based material made with renewable feedstock from non-food competing sources, is produced with 100% renewable electricity.
07/06/2022Plastics are versatile and come in every conceivable shape, size, color, and function. Yet before plastic products can fulfill their desired function, they are subject to testing to confirm they comply with various standards. It takes testing labs hours, if not days, to create a quote for materials testing.
06/06/2022The BMW Group is the first automotive manufacturer to use OEM coatings from BASF that are certified according to the biomass balance process. By using new sustainable product variants, around 40% CO2 can be avoided for clear coat and dip coating.
01/06/2022The companies Dow (NYSE: DOW), LOVERE, YCJ and Procter & Gamble (P&G) will organize the first "Design for Circularity" art and design competition in China.
23/05/2022In the HITCOMP project (High Temperature Characterization and Modelling of Thermoplastic Composites), thermoplastic materials were investigated in the aerospace sector. The researchers concluded that thermoplastic-based components are more efficient than thermosetting plastic composites in terms of their thermal properties.
09/05/2022The two companies Brüskem and Sojitz cooperate within a partnership to produce and market the bioMEG (monoethylene glycol) and bioMPG (monopropylene glycol). This joint venture aims to promote sustainable development and combine the expertise of both companies.
09/05/2022High-quality face masks made in Austria by Grabher contain fully recyclable meltblown polypropylene supplied by Borealis and can be recycled in Austria. The new Partnership between the companies Borealis and Grabher is embodiment of the Borealis EverMinds™ spirit of taking action to accelerate the move towards plastics circularity.
06/05/2022At 16, did you already know where you wanted to go on your professional journey? With the range of choices available to young people today, it can be difficult to make a decision at first glance. That's why it's beneficial to be taken by the hand and introduced to different professions. Wentus GmbH from Höxter sets a good example.
04/05/2022Medical devices made from Solvay's high-performance thermoplastic Udel® are recycled thanks to a collaboration between Solvay and Mitsubishi Chemical Advanced Materials. Solvay knows how to evaluate the chemistry of the end-of-life polymer, while MCAM has expertise in washing and mechanically cleaning the material.
04/05/2022The mission of the new "We are plastics" alliance between the three major German Plastics Associations is to promote the circular economy. They focus on the dialog with consumers and NGOs, on the network between individual initiatives and on presenting facts and changes of the industry.
19/04/2022At 16, did you already know where you wanted to go on your professional journey? With the range of choices available to young people today, it can be difficult to make a decision at first glance. That's why it's beneficial to be taken by the hand and introduced to different professions. Wentus GmbH from Höxter sets a good example.
11/04/2022Twelve Boeing 777-300ERs will gradually be fitted by SWISS with the riblet films developed by Lufthansa Technik and BASF. The reduced frictional resistance makes the sub-fleet more economical and lower in emissions, thus reducing the environmental footprint.
04/04/2022The WITTMANN Group has changed its brand strategy and is aiming for a one-brand strategy instead of the two-brand strategy.
11/03/2022Mentoring in areas such as marketing and sales, direct contact with large companies, and support from industry experts – this is what every start-up dreams of. In the Circular Valley in Wuppertal, Germany, this is reality. Entrepreneurs from a wide variety of fields who want to contribute to the Circular Economy with their work are supported here.
07/03/2022Salmon fillets from Bömlo are supplied in the world's first EPS fish box. Ccycled is made from chemically recycled plastic and BASF, Vartdal Plast and Bremnes Seashore, the partners for this joint project, are contributing to making the circular economy a success.
07/03/2022In order to be able to reuse silicon, a working group from the Fraunhofer Institute for Solar Energy Systems ISE and the largest German recycling company for PV modules, Reiling GmbH & Co. KG, have developed a solution, in which the silicon in the discarded modules was recycled on an industrial scale and reused to produce new PERC solar cells.
21/02/2022To study how much plastic is trickling down on us from the atmosphere, Empa researcher Dominik Brunner, together with colleagues from Utrecht University and the Austrian Central Institute for Meteorology and Geophysics, have developed a chemical method that determines the contamination of the samples with a mass spectrometer.
14/02/2022Neste and Ravago intend to establish a joint venture to build an industrial chemical recycling facility in the North Sea port of Vlissingen, the Netherlands. From there, global chemical recycling activities will be managed, building on the further development of thermochemical liquefaction technology by U.S.-based Alterra Energy, an innovative chemical recycling technology company.
07/02/2022Profine GmbH is the first profile system provider to use polyethylene (PE) packaging foils that consist of 80 percent PCR standard and are interested in making supply chains more environmentally friendly.
19/01/2022Petchem Business Unit Director, MOL Hungarian Oil and Gas Company Plc.
14/01/2022The Institute for Bioplastics and Biocomposites presents the new edition of its brochure with the title "Biopolmers - Facts and statistics" to show how the bioplastics market is developing.
08/12/2021Renewable energies, resource-saving processes, climate neutrality – rising to major challenges is key. These global tasks require creative minds, innovative technologies and high-performance materials.